Reznor MAPS - A,B,C Users Manual Bedienungsanleitung PDF herunterladen (Seite 7)

Form O-MAPSIII&IV Cabinets A/B/C, P/N 257004R8, Page 7

Filter

Clamp

Filter

Wing Screw,

P/N 205707,

and Retainer,

P/N 205709

(2 each)

Filter

FIGURE 2A -

Removing Filters

from Outside

Air Hood

1" Permanent

Aluminum Filters

for Outside Air

Hood are listed by

Cabinet Size A, B, or C

(see cross-reference, page 6)

*A - (4) 16 x 20, P/N 101607

*B - (4) 16 x 25, P/N 101609

C - (3) 16 x 25, P/N 101609;

(6) 16 x 20, P/N 101607

Cabinet Sizes A and B with Option AS16

Outside Air Hood

(Does not apply if

system includes

Option PE

power exhaust;

see below.)

Filter Clamps attach

with Wing Screws

P/N 205707

Filter

16x20x1

Filter

16x20x1

Filter

16x20x1

Filter

16x25x1

Filter

16x25x1

Filter

16x25x1

Filter

16x20x1

Filter

16x20x1

Filter

16x20x1

Inlet View

All Cabinet Size C with

either Outside Air Hood

Option AS16 or AS19

Instructions: Remove lters by loosening the wing screws and sliding the lter

clamp(s). Clean with soap and water, allow to dry, and replace. If it is more convenient

to keep an extra clean set of lters, quantities, lter sizes, and part numbers are listed.

* Apply only to Cabinet

Size A and B with outside

air hood Option AS16



















FIGURE 2B - Removing Filters from Option AS19 Outside Air

Hood Installed on a Cabinet Size A or B with power exhaust

Option PE1 or PE2

Instructions: 1) Remove the four screws as illustrated. Lower the tray.; 2) Pull out

lters. Clean with soap and water. Allow to dry.; 3) Slide clean dry lters into tray.;

4) Re-position tray and replace screws.

1" Aluminum Filters: **A - (4) 18 x 20, P/N 194903; **B - (4) 20 x 25, P/N 101610

** Apply only to Cabinet Size A and B with outside air hood Option AS19.

Permanent Filters in

the Outside Air Hood

If equipped with an outside air hood, there are 1" permanent, aluminum lters at the

entrance of the hood. The lters act as a moisture eliminator and bird screen. See FIG-

URE 2A or 2B. When inspecting the inlet air lters, inspect the outside air hood lters.

If cleaning is needed, remove the lters, clean, rinse, dry and re-install.

Filters in an Optional

Energy Recovery

Module

If equipped with an energy recovery module (Option ER1A, ER1B, or ER1C), check

both inlet and exhaust lters. Replace as needed.

Cabinet

Size *

Inlet Air Filters (Merv 8) Exhaust Air Filters (Merv 8)

Filter Type & Size Qty P/N Filter Type & Size Qty P/N

A Pleated 20x25x2 2 104113 Pleated 20x25x2 2 104113

Pleated 16x25x2 2 104112 Pleated 16x25x2 2 104112

Pleated 12x25x2 2 114320 Pleated 12x25x2 2 114320

Pleated 16x25x2 2 104112 Pleated 16x25x2 2 104112

Pleated 20x25x2 2 104113 Pleated 20x25x2 2 104113

Pleated 16x16x2 1 104109 Pleated 16x16x2 1 104109

Pleated 16x20x2 1 104110 Pleated 16x20x2 1 104110

*See cross-reference of

MAPS

Models by Cabinet

Size A, B, or C on page 6.

3.2 Drive

Components

CAUTION: If the

blower is unused

for more than three

months, bearings

with a grease tting

should be purged

with new grease

prior to startup.

Setscrews - Check all of the setscrews (bearing/blower hubs and pulleys). Torque pul-

ley setscrews a minimum of 110 in-lb to 130 in-lb maximum.

A bearing hub setscrew for a 1-3/8" to 1-3/4" shaft requires a 5/16" socket and a tight-

ening torque of 165 in-lbs.

Belts - Check belt for proper tension and wear. If needed, follow instructions to adjust

belt tension. Replace worn belts.

Bearings - Bearings with a grease tting should be lubricated twice a year with a high

temperature, moisture-resistant grease. (Type NLGI-1 or -2 standard grease is recom-

mended.) Be sure to clean the grease tting before adding grease. Add grease with a

handgun until a slight bead of grease forms at the seal. Be careful not to unseat the

seal by over lubricating. NOTE: If unusual environmental conditions exist (tempera-

tures below 32°F or above 200°F; moisture; or contaminants), more frequent lubrica-

tion is required.

NOTE: If it is more convenient to keep an extra clean set of lters, lter sizes and part numbers are shown in the illustration.

1 2 3 4 5 6 7 8 9 10 11 12 ... 39 40

Kommentare zu diesen Handbüchern

Keine Kommentare

Reznor MAPS - A,B,C Users Manual Bedienungsanleitung Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Heizkörper Reznor MAPS - A,B,C Users Manual